Heat-glo-fireplace Heat-N-Glo 6000XLT-CDN User Manual

1- Do not store or use gasoline or other flam-mable vapors and liquids in the vicinity of thisor any other appliance.- What to do if you smell gas D

10VENT SYSTEMTERMINATION KITSVENT SYSTEM COMPONENTSFigure 5. Vent Components and TerminationsStep 3Installing theVent SystemA. Vent System ApprovalsT

11DV-90D65/3257/873/8DV-45D67/1611 1/1661/285/881/251/168/1211 5/885/811 15/16DV-36D35 3/447 3/4DV-48D5 3/48 3/411 3/4DV-12DDV-09DDV-06D6-5/32"(1

12Figure 7. Straight Up Vertical VentingSTRAIGHT UPVERTICAL VENTINGV (FT.)40' MAX. (12.4 M)NOTE: Model 6000ARCHA 12-inch length of straight ventp

13HORIZONTAL VENTINGHKit No. Max. RunDVK-01DDVK-01TRD 24" (610 mm)NOTE: Models 6000TR and 6000XLS are tested and approved touse 45° elbows in cor

14VENTING WITH ONE (1) 90° ELBOW V (FT.) H (FT.) 1' MIN. (305mm) 2' MAX. (610mm) 2' MIN. (610mm) 4' MAX.

15VENTING WITH ONE (1) 90° ELBOW V (FT.) H (FT.) 1' MIN. (305mm) 5' MAX. (1.52m) 2' MIN. (610mm) 10' MAX. (3.1m)

16VENTING WITH TWO (2) 90° ELBOWSV H H + H11´ MIN. (305 mm) 2´ MAX. (610 mm) 5´ MAX. (1.52m)2´ MIN. (610 mm) 4´ MAX. (1.22 m) 10´ MAX. (3.1m)3´ MIN.

17VENTING WITH TWO (2) 90o ELBOWS V (FT.) H + H1 (FT.)1' MIN. (305mm) 5´ MAX. (1.52m)2' MIN. (610mm) 10´ MAX. (3.1m)3' MIN. (

181´ MIN. (305 mm) 2´ MAX. (610 mm) 5´ MAX. (1.52 m)2´ MIN. (610 mm) 4´ MAX. (1.22 m) 10´ MAX. (3.1 m)3´ MIN. (914 mm) 6´ MAX. (1.86 m) 15´ MAX. (4.

19VENTING WITH THREE (3) 90° ELBOWS V (FT.) H (FT.)1' MIN. (305mm) 5' MAX. (1.52m)2' MIN. (610mm) 10' MAX. (3.1m)3' MIN

2!!!!!!!!!!!!!!!!!!SAFETY AND WARNING INFORMATIONREAD and UNDERSTAND all instructions carefully before starting the installation.FAILURE TO FOLLOW th

20Figure 15 For Model 6000TRB. Installing Vent ComponentsFor Model 6000TRAfter determining which set of starting collars will be used(top or rear)

21WARNING: ENSURE THAT THE FIBER-GLASS ROPE GASKET SUPPLIED WITHTHE FIREPLACE SEALS BETWEEN THEFIRST VENT COMPONENT & THE OUTERFIREPLACE WRAP.1. A

222. Continue Adding Vent ComponentsTo continue adding vent components in accordancewith the pre-planned vent system configuration: Ensure that each

23For Vertical Runs - The vent system must besupported every eight (8) feet (2.4 m) above thefireplace flue outlet by wall brackets.To install support

24TRIM HEATSHIELD IF TOOLONG, ADD TOSHIELD IF TOOSHORTEXTERIORFIRESTOPINTERIORFIRESTOPHEAT SHIELDFigure 20. 12" x 12" Hole and Vent Pipe2. P

25 Drill a hole or drive a nail through this centerpoint. Check the floor above for any obstructions, such aswiring or plumbing runs. Reposition th

26JOISTCEILING FIRESTOPCEILINGNAILS (4 REQUIRED)!If the area above the ceiling IS an attic, position andsecure the firestop on top of the previously f

27For round captermination:1. Secure the 8-5/8inch (219 mm) pipe,using the exteriorpipelock hole on theround flange of thewall firestop.For trapezoida

28V =VENT TERMINALX =AIR SUPPLY INLET=AREA WHERE TERMINAL IS NOT PERMITTEDA = 12" clearances above grade, veranda, porch, deck or balconyB = 12&

29!For Vertical Terminations - To locate the vent andinstall the vent sections: Locate and mark the vent centerpoint on the under-side of the roof, a

3TABLEOFCONTENTSSafety and Warning Information ... 2Section 1: Approvals and Codes ... 4Approval Listings and

30TERMINATIONCAPTo seal the roof hole, and to divert rain and snow fromthe vent system: Attach a flashing to the roof using nails, and use anon-harde

31The diagram below shows how to properly position,level, and secure the fireplace.1. Place the fireplaceinto position.2. Level the fireplacefrom side

32STANDING PILOTNOTE: FLAMES TOOCLOSE TO THECERAMIC INSULATORSCAN CAUSE NUISANCELOCKOUTS ANDELECTRODE FAILURE.DSI IGNITIONFigure 29. Gas Controls Syst

33 At the gas line access hole, use insulation to re-pack the space around the gas pipe. Insert insulation from the outside of the fireplaceand pack

34NOTE: 6000XLT-CDN DOES NOT HAVE A LIMIT SWITCH.!!Figure 31. Standing Pilot Ignition Wiring DiagramStep 8Wiring theFireplaceNOTE: Electrical wiring m

35Figure 32. Fan Wiring DiagramFor Direct Spark Ignition (DSI) WiringAppliance RequirementsThis appliance requires that 110-120 VAC be wired tothe fa

36Figure 33. Direct Spark Ignition (DSI) Wiring DiagramStep 9FinishingThe following diagram shows the minimum verticaland corresponding maximum horizo

37CAUTIONIF JOINTS BETWEEN THE FINISHED WALLS ANDTHE FIREPLACE SURROUND (TOP AND SIDES)ARE SEALED, A 300° F. MINIMUM SEALANTMATERIAL MUST BE USED. TH

38Positioning the LogsIf the gas logs have been factory installed theyshould not need to be positioned.If the logs have been packaged separately, refe

391. Lift the trim door upand out of the unit.EYE BOLTLATCH BRACKETGLASS DOORFigure 38. Placement of the Ember MaterialCAUTIONIT IS STRONGLY RECOMMEND

4Approval Listingsand CodesAppliance CertificationThe Heat-N-Glo models discussed in this InstallersGuide have been tested to certification standardsa

40Before lighting the fireplace, be sure to do thefollowing:Remove all paperwork and documents from thefireplace.Review safety warnings and cautions

41This model is equipped with a baffle which will allow youto control usable heat output. The baffle control lever islocated at the lower left corner

424MaintainingandServicingYourFireplaceFireplaceMaintenanceAlthough the frequency of your fireplace servicing andmaintenance will depend on use and th

43STANDING PILOTFigure 41. Burner Flame PatternsMAKE SURE THE FLAMESARE STEADYNOTLIFTING OR FLOATING.Figure 42. Pilot/Ignitor Flame PatternsDSI IGNIT

52GettingStartedHeat-N-Glo direct vent gas fireplaces are designed tooperate with all combustion air siphoned from outsideof the building and all exha

6Figure 1. Diagram of the 6000TR, 6000XLT-CDN and 6000XLSThe Heat-N-Glo Warranty will be voided by, and Heat-N-Glo disclaims anyresponsibility for, th

7Figure 2. Diagram of the 6000ARCH

83Installing theFireplaceStep 1Locating theFireplaceThe diagram below shows space and clearancerequirements for locating a fireplace within a room.MOD

9ABCFraming should beconstructed of 2 X 4lumber or heavier.Model A B C D E6000TR 42 38 1/4 22 42 26 1/46000XLS 42 38 1/4 22 N/A 26 1/46000XLT-CDN 42