1Heat & Glo • GEM42 • 371-900 Rev. N • 2/05- Do not store or use gasoline or other flam-mable vapors and liquids in the vicinity of thisor
10Heat & Glo • GEM42 • 371-900 Rev. N • 2/053Installing the FireplaceStep 1. Locating the FireplaceThe following diagram shows space
11Heat & Glo • GEM42 • 371-900 Rev. N • 2/05Framing should beconstructed of 2 X 4lumber or heavier.A. ... 47-1/2”B. ...
12Heat & Glo • GEM42 • 371-900 Rev. N • 2/05NOTE: PIPES OVERLAP 1-1/4 INCHESAT EACH JOINT.Figure 4. DVP-Series Direct Vent Component Sp
13Heat & Glo • GEM42 • 371-900 Rev. N • 2/05Figure 5. Vent System Components and Termination KitsStep 3. Installing the Vent SystemA. Ven
14Heat & Glo • GEM42 • 371-900 Rev. N • 2/05FLUERESTRICTORFigure 9PILOT SHIELDPILOTBRACKETPILOT SHIELD SHOULD BECLOSED AND TOUCHINGTHE PILO
15Heat & Glo • GEM42 • 371-900 Rev. N • 2/05VENTING WITH ONE (1) 90° ELBOW V (FT.) H (FT.) 2' MIN. (.609m) 3' M
16Heat & Glo • GEM42 • 371-900 Rev. N • 2/05VENTING WITH THREE (3) 90° ELBOWS V (FT.) H (FT.) 2' MIN. (.609m) 3' MAX. (.
17Heat & Glo • GEM42 • 371-900 Rev. N • 2/05B. Installing Vent ComponentsVenting Out the Top VentThe glass must be taken off again for pos
18Heat & Glo • GEM42 • 371-900 Rev. N • 2/054. Install FirestopsFor Horizontal Runs - Firestops are REQUIRED on bothsides of a combustible
19Heat & Glo • GEM42 • 371-900 Rev. N • 2/05!C. Vent TerminationFor Horizontal Terminations - To attach and secure thetermination to the l
2Heat & Glo • GEM42 • 371-900 Rev. N • 2/05These units MUST use one of the vent systemsdescribed in the Installing the Fireplace section of
20Heat & Glo • GEM42 • 371-900 Rev. N • 2/05V= VENT TERMINALX= AIR SUPPLY INLET= AREA WHERE TERMINAL IS NOT PERMITTED Figure 21. Vent
21Heat & Glo • GEM42 • 371-900 Rev. N • 2/05For Vertical Terminations - To locate the vent and installthe vent sections:• Locate and mark t
22Heat & Glo • GEM42 • 371-900 Rev. N • 2/05Step 5. Installing the Optional Heat-Out or Heat-Zone KitsFigure 243. Cut and frame a 12” wi
23Heat & Glo • GEM42 • 371-900 Rev. N • 2/05• At the gas line access hole, use insulation to re-packthe space around the gas pipe.• Insert
24Heat & Glo • GEM42 • 371-900 Rev. N • 2/05!!Figure 26. Intermittent Pilot Ignition (IPI) Wiring DiagramNOTE 1: Ignition module, valve, pi
25Heat & Glo • GEM42 • 371-900 Rev. N • 2/05FINISH WALL MATERIALMUST BE NON-COMBUSTIBLE - TOP AND SIDES60” 52”NON-COMBUSTIBLEStep 10. Fini
26Heat & Glo • GEM42 • 371-900 Rev. N • 2/05Facing RequirementsFacing Thickness from 3/4” to 1-1/4”Facing material within this thickness ra
27Heat & Glo • GEM42 • 371-900 Rev. N • 2/05Installing the TrimCombustible materials may be brought up to the specifiedclearances on the si
28Heat & Glo • GEM42 • 371-900 Rev. N • 2/05Step 12. Before Lighting the FireplaceBefore lighting the fireplace, be sure to do the follow
29Heat & Glo • GEM42 • 371-900 Rev. N • 2/054Maintaining and Servicing Your FireplaceFireplace MaintenanceAlthough the frequency of your fi
3Heat & Glo • GEM42 • 371-900 Rev. N • 2/05TABLE OF CONTENTSSafety and Warning Information ...
4Heat & Glo • GEM42 • 371-900 Rev. N • 2/05* Part number list on following page.* La liste des numéros de pièce se trouve à la page suiv
5Heat & Glo • GEM42 • 371-900 Rev. N • 2/05ITEM /PIÈCEDESCRIPTIONSERIAL # / N° DE SÉRIEPART NUMBER/ N° DE PIÈCE1 Heat Shield / Protection
6Heat & Glo • GEM42 • 371-900 Rev. N • 2/05(NG, LP) Exploded Parts Diagram(GN, PL) Vue éclatée des piècesService PartsIntermittent Pilot
7Heat & Glo • GEM42 • 371-900 Rev. N • 2/05Appliance CertificationThe Heat & Glo fireplace model discussed in this InstallersGuide has
8Heat & Glo • GEM42 • 371-900 Rev. N • 2/052Getting StartedIntroducing the Heat & Glo Gas FireplacesHeat & Glo direct vent gas fire
9Heat & Glo • GEM42 • 371-900 Rev. N • 2/05Figure 1. Diagram of the GEM42TOP STANDOFFSTOP VENTCOLLARSTRIM DOORRATNG PLATESAND LABELSGASCONT
Comments to this Manuals